Step 1: Prepare Systems for Enterprise ColumnStore 23.02 Nodes
This page details step 1 of a 5-step procedure for deploying Single-Node Enterprise ColumnStore 23.02 with Local storage.
This step prepares the system to host MariaDB Enterprise Server 10.6 and MariaDB Enterprise ColumnStore 23.02.
Interactive commands are detailed. Alternatively, the described operations can be performed using automation.
Optimize Linux Kernel Parameters
MariaDB Enterprise ColumnStore performs best with Linux kernel optimizations.
To optimize the kernel:
Set the relevant kernel parameters in a sysctl configuration file. To ensure proper change management, use an Enterprise ColumnStore-specific configuration file.
# minimize swapping vm.swappiness = 1 # Increase the TCP max buffer size net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 # Increase the TCP buffer limits # min, default, and max number of bytes to use net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 65536 16777216 # don't cache ssthresh from previous connection net.ipv4.tcp_no_metrics_save = 1 # for 1 GigE, increase this to 2500 # for 10 GigE, increase this to 30000 net.core.netdev_max_backlog = 2500
sysctlcommand to set the kernel parameters at runtime
$ sudo sysctl --load=/etc/sysctl.d/90-mariadb-enterprise-columnstore.conf
Temporarily Configure Linux Security Modules (LSM)
The Linux Security Modules (LSM) should be temporarily disabled on each Enterprise ColumnStore node during installation.
The LSM will be configured and re-enabled later in this deployment procedure.
The steps to disable the LSM depend on the specific LSM used by the operating system.
CentOS / RHEL Stop SELinux
SELinux must be set to permissive mode before installing MariaDB Enterprise ColumnStore.
To set SELinux to permissive mode:
Set SELinux to permissive mode:
$ sudo setenforce permissive
Set SELinux to permissive mode by setting
For example, the file will usually look like this after the change:
# This file controls the state of SELinux on the system. # SELINUX= can take one of these three values: # enforcing - SELinux security policy is enforced. # permissive - SELinux prints warnings instead of enforcing. # disabled - No SELinux policy is loaded. SELINUX=permissive # SELINUXTYPE= can take one of three values: # targeted - Targeted processes are protected, # minimum - Modification of targeted policy. Only selected processes are protected. # mls - Multi Level Security protection. SELINUXTYPE=targeted
Confirm that SELinux is in permissive mode:
$ sudo getenforce Permissive
SELinux will be configured and re-enabled later in this deployment procedure. This configuration is not persistent. If you restart the server before configuring and re-enabling SELinux later in the deployment procedure, you must reset the enforcement to permissive mode.
Debian / Ubuntu AppArmor
AppArmor must be disabled before installing MariaDB Enterprise ColumnStore.
$ sudo systemctl disable apparmor
Reboot the system.
Confirm that no AppArmor profiles are loaded using
$ sudo aa-status
apparmor module is loaded. 0 profiles are loaded. 0 profiles are in enforce mode. 0 profiles are in complain mode. 0 processes have profiles defined. 0 processes are in enforce mode. 0 processes are in complain mode. 0 processes are unconfined but have a profile defined.
AppArmor will be configured and re-enabled later in this deployment procedure.
Configure Character Encoding
When using MariaDB Enterprise ColumnStore, it is recommended to set the system's locale to UTF-8.
On RHEL 8, install additional dependencies:
$ sudo yum install glibc-locale-source glibc-langpack-en
Set the system's locale to
$ sudo localedef -i en_US -f UTF-8 en_US.UTF-8
This page was step 1 of 5.