InnoDB Buffer Pool
The XtraDB/InnoDB buffer pool is a key component for optimizing MariaDB. It stores data and indexes, and you usually want it as large as possible so as to keep as much of the data and indexes in memory, reducing disk IO, as main bottleneck.
How the Buffer Pool Works
The buffer pool attempts to keep frequently-used blocks in the buffer, and so essentially works as two sublists, a new sublist of recently-used information, and an old sublist of older information. By default, 37% of the list is reserved for the old list.
When new information is accessed that doesn't appear in the list, it is placed at the top of the old list, the oldest item in the old list is removed, and everything else bumps back one position in the list.
When information is accessed that appears in the old list, it is moved to the top the new list, and everything above moves back one position.
The most important server system variable is innodb_buffer_pool_size, which you can set from 70-80% of the total available memory on a dedicated database server with only or primarily XtraDB/InnoDB tables.
Be aware that the total memory allocated is about 10% more than the specified size as extra space is also reserved for control structures and buffers. The space must also be contiguous. If you're running a Windows system that loads DLL's at specific addresses, this may cause difficulties.
The larger the size, the longer it will take to initialize. On a modern 64-bit server with a 10GB memory pool, this can take five seconds or more.
Make sure that the size is not too large, causing swapping. The benefit of a larger buffer pool size is more than undone if your operating system is regularly swapping.
If innodb_buffer_pool_size is set to more than 1GB, innodb_buffer_pool_instances divides the InnoDB buffer pool into a specific number of instances. The default was 1 in MariaDB 5.5, but for large systems with buffer pools of many gigabytes, many instances can help reduce contention concurrency. The default is 8 in MariaDB 10.0, with the exception of 32-bit Windows, where it depends on the value of innodb_buffer_pool_size. Each instance manages its own data structures and takes an equal portion of the total buffer pool size, so for example if innodb_buffer_pool_size is 4GB and innodb_buffer_pool_instances is set to 4, each instance will be 1GB. Each instance should ideally be at least 1GB in size.
innodb_old_blocks_pct and innodb_old_blocks_time
The default 37% reserved for the old list can be adjusted by changing the value of innodb_old_blocks_pct. It can accept anything between between 5% and 95%.
The innodb_old_blocks_time variable specifies the delay before a block can be moved from the old to the new sublist.
0, the MariaDB 5.5 default, means no delay, while the default has been set to
1000 since MariaDB 10.0.
Before changing either of these values from their defaults, make sure you understand the impact and how your system currently uses the buffer. Their main reason for existence is to reduce the impact of full table scans, which are usually infrequent, but large, and previously could clear everything from the buffer. Setting a non-zero delay could help in situations where full table scans are performed in quick succession.
Temporarily changing these values can also be useful to avoid the negative impact of a full table scan, as explained in InnoDB logical backups.
Dumping and Restoring the Buffer Pool
When the server starts, the buffer pool is empty. As it starts to access data, the buffer pool will slowly be populated. As more data will be accessed, the most frequently accessed data will be put into the buffer pool, and old data may be evicted. This means that a certain period of time is necessary before the buffer pool is really useful. This period of time is called the warmup.
Since MariaDB 10.0, InnoDB can dump the buffer pool before the server shuts down, and restore it when it starts again. If this feature is used, no warmup is necessary. To enable the buffer pool dump at shutdown and the restore at startup respectively, the innodb_buffer_pool_dump_at_shutdown and innodb_buffer_pool_load_at_startup system variables can be set to ON.
It is also possible to dump the InnoDB buffer pool at any moment while the server is running, and it is possible to restore the last buffer pool dump at any moment. To do this, the special innodb_buffer_pool_dump_now and innodb_buffer_pool_load_now system variables can be set to ON. When selected, their value is always OFF.
A buffer pool restore, both at startup or at any other moment, can be aborted by setting innodb_buffer_pool_load_abort to ON.
The file which contains the buffer pool dump is specified via the innodb_buffer_pool_filename system variable.