MaxScale Simple Sharding with Two Servers
Simple Sharding with Two Servers
Sharding is the method of splitting a single database server into separate parts. This tutorial describes a very simple way of sharding. Each schema is located on a different database server and MaxScale's schemarouter module is used to combine them into a single database server.
MaxScale will appear to the client as a database server with the combination of all the schemas in all the configured servers.
Environment & Solution Space
This document is designed as a simple tutorial on schema-based sharding using MaxScale in an environment in which you have two servers. The object of this tutorial is to have a system that, to the client side, acts like a single MySQL database but actually is sharded between the two servers.
The process of setting and configuring MaxScale will be covered within this document. The installation and configuration of the MySQL servers will not be covered in-depth. The users should be configured according to the configuration guide.
This tutorial will assume the user is running from one of the binary distributions available and has installed this in the default location. Building from source code in GitHub is covered in guides elsewhere as is installing to non-default locations.
The steps involved in creating a system from the binary distribution of MaxScale are:
Install the package relevant to your distribution
Create the required users on your MariaDB or MySQL server
Create a MaxScale configuration file
The precise installation process will vary from one distribution to another details of what to do with the RPM and DEB packages can be found on the download site when you select the distribution you are downloading from. The process involves setting up your package manager to include the MariaDB repositories and then running the package manager for your distribution, RPM or apt-get.
Upon successful completion of the installation command you will have MaxScale installed and ready to be run but without a configuration. You must create a configuration file before you first run MaxScale.
Creating Your MaxScale Configuration
The first step in the creation of your maxscale.cnf file is to define the global maxscale section. This section configures the number of threads MaxScale uses. A good rule of thumb is to use at most as may threads as you have CPUs. MaxScale uses few threads for internal operations so one or two threads less than the maximum should be enough.
After this we configure two servers we will use to shard our database. The
accounts_east server will hold one schema and the
accounts_west will hold another schema. We will use these two servers to create our sharded database.
[accounts_east] type=server address=192.168.56.102 port=3306 [accounts_west] type=server address=192.168.122.85 port=3306
The next step is to configure the service which the users connect to. This section defines which router to use, which servers to connect to and the credentials to use. The router we use in this tutorial is the
[Sharded Service] type=service router=schemarouter servers=accounts_west,accounts_east user=sharduser passwd=YqztlYGDvZ8tVMe3GUm9XCwQi
After this we configure a listener for the service. The listener is the actual port the user connects to. We will use the port 4000.
[Sharded Service Listener] type=listener service=Sharded Service protocol=MySQLClient port=4000
The final step is to configure a monitor which will monitor the state of the servers. The monitor will notify MaxScale if the servers are down. We add the two servers to the monitor, define the credentials to use and we set the monitoring cycle interval.
[MySQL Monitor] type=monitor module=mysqlmon servers=accounts_west,accounts_east user=monitoruser passwd=7SP1Zcsow8TG+9EkEBVEbaKa monitor_interval=1000
After this we have a fully working configuration and we can move on to starting MaxScale.
Upon completion of the configuration process MaxScale is ready to be started . This may either be done manually by running the maxscale command or via the service interface. The service scripts are located in the
/etc/init.d/ folder and are accessible through both the
After starting MaxScale check the error log in /var/log/maxscale to see if any errors are detected in the configuration file. Also the maxadmin command may be used to confirm that MaxScale is running and the services, listeners etc have been correctly configured.
MaxScale is now ready to start accepting client connections and routing them. Queries are routed to the right servers based on the database they target and switching between the shards is seamless since MaxScale keeps the session state intact between servers.